60 Search Results

Rare earth (RE)-based materials have unique electronic, magnetic, and optical properties, leading to the recent discovery of atomically layered solids with the chemical formula (M'_2/3RE_1/3)₂AlC, which have since garnered significant attention in the scientific community. This study aims to synthesize, characterize, and investigate the structural and thermal stability of the RE i-MAX phases. We prepared i-MAX phases using molybdenum (Mo) as M′ and RE elements as Dy, Tb, and Er, namely (Mo_2/3Dy_1/3)₂AlC, (Mo_2/3Tb_1/3)₂AlC, and (Mo_2/3Er_1/3)₂AlC. Structural characterization through x-ray diffraction (XRD) and Raman spectroscopy confirms the formation of the RE-based i-MAX phase, along with the presence of minor impurity phasesmore » in the alloys. Thermogravimetric analysis (TGA) conducted up to 1000°C under ambient conditions reveals that the i-MAX phases remain thermally stable up to approximately 450°C, beyond which oxidation leads to a noticeable weight gain in all samples. Differential scanning calorimetry (DSC) measurements during heating and cooling cycles show endothermic and exothermic peaks for (Mo_2/3Dy_1/3)₂AlC i-MAX in the 410–420°C range, indicating a temperature-induced minor atomic arrangement. In contrast, these peaks are absent in the Tb- and Er-based i-MAX phases. These findings offer valuable insights into the thermal behavior and stability of these i-MAX phases under thermal stress, contributing to a deeper understanding of their unique properties. Furthermore, first-principles density functional theory (DFT) calculations were performed to investigate the electronic and optical properties of the i-MAX phases. The results reveal their metallic nature, with pronounced contributions from Mo and RE elements near the Fermi level and within the conduction band.« less

Resolving molecular chirality on the atomic scale remains a critical challenge in chemistry. Conventional Optical Circular Dichroism spectroscopy often overlooks subtle and localized structural features. Here, we computationally investigate site-specific X-ray circular dichroism (XCD) across a series of trans-azobenzene derivatives to deconstruct and interpret chiroptical signals at the atomic level. Our modeling reveals that XCD is capable of distinguishing dichroic contributions arising from both a local chiral center and a global molecular twist, revealing their intricate interplay and potential for constructive or destructive interference. We show that sterically induced global distortions can dominate the XCD signal in some cases, evenmore » suppressing the response from the chiral center itself. This insight suggests a new molecular design principle for tuning the chiroptical activity, which we extend by proposing strategies to achieve unidirectional photoisomerization through steric gearing. Altogether, this work establishes a quantitative framework for engineering chiroptical responses, laying the foundation for the design of functional chiral systems utilizing principles of unidirectional molecular motor-like conformational dynamics.« less

Nuclear material operations pose unique hazards that are not encountered in other chemical, energy, or manufacturing industries. One of these hazards is the potential for a nuclear criticality accident when handling fissile isotopes such as ²³⁵U and ²³⁹Pu. These hazards are particularly high when fissile material is dissolved in solution as the neutron behaviors of the system can change rapidly with the physical and chemical changes accessible in solution. Current estimates of solution density used for criticality safety are outdated and hinder fissile material handling. Developing new estimates for these safety calculations requires experimental characterization and the derivation of empiricalmore » density models. We have derived a density law describing PuCl₃/HCl/H₂O solutions from experimental data characterizing solution density. Density data was treated using a Pitzer-derived eight-parameter equation, defining density as a function of analyte concentrations, temperature, and interactions between these variables. The model is predictive across the concentration and temperature ranges from which it was derived. The potential effects of varying oxidation states of plutonium, which are easily accessible in aqueous media, on the bulk solution density of the ternary system were also investigated. The resulting Pitzer-derived density law was applied to a nuclear criticality safety model, and the impact of the experimental characterization of solution density relative to previous estimates was demonstrated to be significant and suggest that the current approach to estimating density in nuclear criticality safety calculations may lead to overly conservative controls.« less

Canopy height models (CHMs) with sufficient resolution to distinguish individual trees are useful for a variety of applications. However, standard techniques to acquire such data, such as airborne lidar surveying, are often prohibitively expensive. Deep learning techniques for generating CHMs from high-resolution imagery are an attractive option to reduce costs. To date, success with these methods has been demonstrated using multichannel aerial photography and specialized satellite data products derived from multiple sensors, neither of which is commonly available at temporal resolutions finer than one year. Here we demonstrate a method to generate sub-meter resolution CHMs in three forests in Californiamore » using a more abundant data source: sub-meter resolution, panchromatic satellite imagery from a single sensor. We show that phenology and species composition play important roles in model transferability; when trained using imagery from a single conifer forest in autumn, the model performs well on autumn imagery from a second conifer forest several hundred kilometers distant with no re-training. With modest additions to the training dataset, the same model generates minimally biased estimates of canopy height in both conifer and deciduous forests during multiple seasons. Because the model operates on satellite data with global coverage and a relatively short return interval, we propose its suitability to extrapolate tree-level canopy height data to remote regions and conduct high-temporal resolution monitoring of forest structure. We furthermore demonstrate the workflow’s applicability to fire modeling by conducting simulations in forests populated by trees measured using both this approach and airborne lidar surveying. We find minimal differences in fire behavior relative to a baseline case in which only statistical distributions of tree height and crown area are known. This result underscores the value of forest structural information derived from our workflow for improving the fidelity of wildland fire simulations, among other ecological applications.« less

MoS₂ coatings are used extensively in aerospace and defense applications due to their ultralow friction and high wear resistance. Burnished and resin-bonded MoS₂ coatings are commonly used in these applications due to simplicity in deposition and history of use, despite issues with consistency in coating properties and performance. Physical vapor deposition (PVD) of MoS₂ thin films has emerged as a process alternative in the past 50 years, promising far greater control over film structure and composition but at a greater cost. Despite PVD’s benefits, hesitance to adoption persists in high-consequence applications, not only due to increased costs but variability inmore » resulting coating properties. These variations in properties and subsequent performance are in part due to the complexity of the PVD process and the sensitive interplay between coating process-structure-property relationships. This work aims to demystify the remaining uncertainties of the process-structure-property relationships in PVD MoS₂. The microstructure and mechanical and tribological properties of 61 different PVD pure MoS₂ coatings are examined herein. Emphasis has been placed on developing performance-based (i.e., hardness, modulus) metrics that can assess microstructural changes (density, orientation, and crystallinity) and be utilized to accelerate process development and coating optimization. Relationships established within suggest that nanoindentation hardness can be used to infer coating performance (i.e., wear rate) and properties (i.e., density, crystalline texture, and stoichiometry). Furthermore, this work demonstrates that PVD MoS₂ coatings close to the theoretical density of MoS₂ consistently have the best tribological performance and can be reliably identified by their hardness.« less

In this paper we report on the development and demonstration of density feedback control for MAST-U. Sinusoidal perturbations are used to measure the frequency response from a deuterium gas valve (actuator) to line-integrated core electron density measured by the interferometer (sensor). In the frequency range relevant for control design, only two system-identification experiments were needed to regress a first-order dynamic model. This control-oriented model informs the offline design of a proportional integral controller with the established loop-shaping controller design method. After offline verification of the controller implementation, control is demonstrated by experimentally tracking a staircase reference for the line-integrated electronmore » density. This paper demonstrates the efficiency of controller design using system-identification and loop-shaping, providing reliable density control for MAST-U.« less

Radioisotopes and hazardous gases can have undetermined environmental pathways. Researchers at Pacific Northwest National Laboratory constructed a chamber that complies with the requirements needed for an atmospheric reaction platform and the safety principles of interacting with hazardous dispersible sources to enable the environmental testing of these gases. Initial dynamic testing showed inter-chamber mixing completed from minutes to 1.5 hours. The photooxidation of butyl iodine showed the presence of signals from reaction products, and intermediaries for up to 50 hours. Current detection limits of the chamber and analytical collection and testing approach were shown to be in the single-digit parts permore » billion levels. In conclusion, the comparisons between the measured oxidation trends and literature show the utility of performing laboratory experiments to validate the results of modeling for larger-scale scenarios.« less

We previously documented geographic distributions of the optically brightest lightning on Earth—known as “superbolts”—using two space-based instruments: the photodiode detector (PDD) on the Fast On-orbit Recording of Transient Events (FORTE) satellite and the Geostationary Lightning Mapper (GLM) on NOAA's Geostationary Operational Environmental Satellites. In this study, we further examine the superbolts identified by the PDD and GLM to reconcile the differences between their geographic distributions. We find that both the physical extent of the parent flash and the development speed of its leaders are important for making a superbolt. The oceanic PDD superbolts tend to occur early in flashes thatmore » rapidly expand laterally into long horizontal “megaflashes.” The top GLM superbolts occur over land at later times in particularly large megaflashes. These land-based flashes grow more slowly until they extend over multiple hundreds of kilometers. The FORTE PDD missed these delayed superbolts due to limitations in its triggering. Coincident Tropical Rainfall Measuring Mission measurements show that the warm season megaflash superbolts detected by Lightning Imaging Sensor/GLM and wintertime oceanic superbolts observed by the PDD occur in otherwise similar thunderstorm environments. Both are marked by: low storm heights (<10 km), widespread precipitation near the surface, small infrared brightness temperature gradients, and low flash rates. We suggest that the vertically compact, stratiform nature of these clouds provides favorable conditions for superbolt production.« less

A novel approach to producing corn stover biomass feedstock has been investigated. In this approach, corn grain and stover are co-harvested at moisture contents much less than typical corn silage. The grain and stover are conserved together by anaerobic storage and fermentation and then separated before end use. When separated from the stover, the moist, fermented grain had physical characteristics that differ from typical low-moisture, unfermented grain. A comprehensive study was conducted to quantify the physical properties of this moist, fermented grain. Six corn kernel treatments, either fermented or unfermented, having different moisture contents, were used. Moist, fermented kernels (26more » and 36% w.b. moisture content) increased in size during storage. The fermented kernels’ widths and thicknesses were 10% and 15% greater, respectively, and their volume was 28% greater than the dry kernels (15% w.b.). Dry basis particle density was 9% less for moist, fermented kernels. Additionally, the dry basis bulk density was 29% less, and the dry basis hopper-discharged mass flow rate was 36% less. Moist, fermented grain had significantly greater kernel-to-kernel coefficients of friction and angles of repose compared to relatively dry grain. The friction coefficient on four different surfaces was also significantly greater for fermented kernels. Fermented corn kernels had lower individual kernel rupture strengths than unfermented kernels. These physical differences must be considered when designing material handling and processing systems for moist, fermented corn grain.« less

Understanding whether invasive and native species compete for shared resources where they co-occur is essential for mitigating the negative impacts of invasive species on native ecosystems. Here, we examined how the presence and density of an invasive species, wild pigs (Sus scrofa), affect native white-tailed deer (Odocoileus virginianus; hereafter, deer) on the Savannah River Site, SC, USA. We examined potential changes in deer areas of use, temporal overlap, and occupancy to evaluate the effects of wild pig occurrence and density on deer space use, diel activity, and co-occurrence with wild pigs across 9 months during 2018 and 2019. Wild pigmore » density had the strongest effect on deer space use in high- and moderate-use areas. Declines in deer space use in response to wild pig density were most pronounced in March and October 2018 and April 2019 for females, while male space use declined in response to wild pig density in October and December 2018. Both species were largely nocturnal with high overlap in diel activity across months. Deer occupancy responses to wild pig density varied across months, with negative responses in May and October 2018 and positive responses in July 2018 and April 2019. Deer and wild pigs co-occurred at 30%–59% of camera stations across months, with broadscale co-occurrence patterns being unaffected by changes in shared cover or wild pig occurrence. Overall, our results suggest that deer make fine-scale behavioral adjustments to avoid wild pigs, providing evidence that competition is likely occurring even where wild pig density is relatively low. Such fine-scale behavioral plasticity in deer appears to mitigate the costs of competition with wild pigs and may be a mechanism enabling long-term co-existence of deer and wild pigs. Our study provides novel insight on the complexities of spatiotemporal relationships between invasive wild pigs and native deer and suggests that the negative effects of interactions between deer and wild pigs may be more pronounced when deer life history needs are particularly demanding. In areas where eradication of invasive wild pigs may be impossible, maintaining low wild pig densities may help mitigate, but may not eliminate, the negative effects of wild pigs on deer.« less